We use cookies to optimize our website for you and to be able to continuously improve it. By continuing to browse the site you are agreeing to our use of cookies.
Disagree

Fresatrici universali a mensola DMG MORI DMP 35

macchine per lavorazione dei metalli / fresatrici / Fresatrici universali a mensola

TOP
Seller

Fabbricante: DMG MORI

Modello:DMP 35

Tipo di macchina: Fresatrici universali a mensola

Numero di articolo: 166605707

Quantità: 1

Data: 11.09.2025

Luogo: Land-de Germania

Prezzo:


Seller-item-No.:051095


General
High dynamic Vertical Drill-Tap centre with best milling performance; Control: 3D-control Siemens 840D sl Operate
Working area 1
Longitudinal 350 mm
Cross 420 mm
Vertical 380 mm
Technical Data
Feed rate longitudinal/transverse/vertical 60000/60000/60000 mm/min
Rapid traverse longitudinal/transverse/vertical 60/60/60 m/min


Main drive Drive power (100% DC) 6 kW
Drive power (40% DC) 8,5 kW
Torque (100% DC) 41 Nm
Torque (40% DC) 48 Nm
Speed range 20 - 15000 rpm
Spindle taper BT 30
Clamping System ISO 7388-3 - JD30
Integrated swivel rotary table simultaneous Integated swivel rotary table DMP 35 version 5-Axis simultaneous mode! Torque drives incl. direct measuring in A- and C-Axis Swivel range A-Axis -120 / + 100 degrees Max. load C-axis 100kg Table diameter C-Axis d290mm Rotary joint, 4-channels Inclusive So
Rotary joint, 6 channels Rotary lead through for integrated swivel rotary table with torque drives 6- flute, 2x for air, 4x for oil Including fix plate and fast coupling at machine side
Tool magazine 25 places Tool magazine 25 places (suitable for inclusion in the tool spindle) Max. tool length 150 mm Chip-to-chip time 1.6 sec Note: machine width increases to 1410 mm!
Production package band filter ICS 40bar Paper band filter ICS 40bar includes: Paper band filter 40bar/ 23l/min Additional tank 600l Chip conveyor useable for fine chips (self cleaning slotted filter) Discharge height: 600mm; Tank volume 200l Flushing in working room Spray gun for swarf removal
Air blast through spindle centre Air blast through spindle center via M-Command; maintained air with small Oil portion Due to needed lead through in main spindle only with swarf removal package ICS possible!
RENISHAW touch probe-Kit RENISHAW measuring suitable to tool taper System in Spindle OMP40-2 touch probe with optical signal transmission OTS wireless probe with air purge on machine table OMI-2T optical transmission module Plastic carrying case Calibration tool incl. tool holder
Preparation 3D Quickset Machine preparation for use of the 3D quickSET Toolkit. included is the Softwareoption for 3D quickSET for one machine. 5 axis machine configurations (only with option touch probe)
proTIME proTIME Visualisation of remaining runtime, remaining workpieces and the machine state
Signal lamp 4-colour Signal lamp, 4 colours
Automation Interface WH CELL right Automation interface right for WH CELL / WH FLEX Interface (Profibus) via M65; Automatic loading door right; Working table with 4-channel rotary joint; 4-chanel enegry supply to machine table for (3-Axis-Machines); Only in combination with an additional c
Price reduction for automation from DMG MORI Price reduction on automation interface with simultaneous order of a DMG MORI Automation solution
Operation mode 4 Operation mode 4 Process monitoring in the production Manual intervention with open doors of machining area. Release after check list has been filled in.
Digital Manufacturing Package Digital Manufacturing Package (1) IoTconnector Allows the use of the Online services from DMG MORI (2) Machine Data Connector (MDC) Standardized machine data interface Protocols: OPCUA, MTConnect, MQTT (3) NETservice Qualified support through internet-b
Messenger V4 The latest version of DMG MORI Messenger displays web based the machine live status. It allows to analyze the machine run-time, downtime, alarms in individually configurable dashboards and transparently shows the actual status in the manufacturing shop
Workpiece loading & unloading system WH 3 CELL Workpiece loading & unloading system WH 3 CELL with 6-axis industrial robots and workpiece carrier storing system (paternoster); maximum possible workpiece weight of 3 kg, maximum workpiece size 100 x 100 x 50 mm Robot FANUC LR Mate 200 iD/7L D5952871 PROFIBUS in
Pneumatic pallet pusher - robot side Pneumatic cylinder installed on the robot side for slide over individual workpiece pallets within the paternoster system.
Menu-driven input programming Menu-driven input programming Control extension in addition to the Teach programming; Process definition by entering parameters; Separate intuitive user interface;
Robot FANUC LR Mate 200 iD/14L Robot FANUC LR Mate 200 iD/14L for Load capacity extension up to 14 kg transfer weight (deviating axis speeds to robot FANUC LR Mate 200 iD/7L!)
WH 3 CELL Integration kit for DMP 35/70 WH 3 CELL Integration kit for DMP 35/70 Machine-specific adaptation for the protective housing on one DMP 35/70
Dual gripper PGN 80 (without gripper fingers) Dual gripper Type Schunk PGN 80 with 8 mm travel per jaw (gripper fingers not included!)
Gripper quick-change system 2 gripper Gripper quick-change system for dual gripper
Workpiece carrier standard Workpiece carrier standard - plastic 15 Workpiece carrier 600x400 (workpiece specified inlay´s not include)
SPC drawer SPC drawer (only to be removed) Output of a trial workpiece for process control
Turning station (without gripper fingers) Turning station includes 1 gripper, type depending on the selection and rotary module 0° / 180° (gripper fingers not included!)
Alignment station Alignment station for exact positioning of the workpiece in the gripper.
Robot Teachset Robot Teachset for the new creation of workpieces / workpiece carriers as well as for the basic adjustment of the robot and / or gripper.
Not OK discharge via slide Not OK discharge via slide Removal of bad parts after machine signal
Special equipment 1 set of gripper jaws for turning station Design analogous to gripper jaw set PGN+80 2 sets of gripper fingers for gripper unit Design analogous to gripper jaw set PGN+80, suitable for gripper unit and quick-change gripper finger system 1 piece workpiec
Condividi questa macchina su Facebook:

Inchiesta

Commerciante di macchine?

Si prega di rimettere in opzione

Inviare la domanda desiderato?

Copia a voi?

Save input data


General
High dynamic Vertical Drill-Tap centre with best milling performance; Control: 3D-control Siemens 840D sl Operate
Working area 1
Longitudinal 350 mm
Cross 420 mm
Vertical 380 mm
Technical Data
Feed rate longitudinal/transverse/vertical 60000/60000/60000 mm/min
Rapid traverse longitudinal/transverse/vertical 60/60/60 m/min


Main drive Drive power (100% DC) 6 kW
Drive power (40% DC) 8,5 kW
Torque (100% DC) 41 Nm
Torque (40% DC) 48 Nm
Speed range 20 - 15000 rpm
Spindle taper BT 30
Clamping System ISO 7388-3 - JD30
Integrated swivel rotary table simultaneous Integated swivel rotary table DMP 35 version 5-Axis simultaneous mode! Torque drives incl. direct measuring in A- and C-Axis Swivel range A-Axis -120 / + 100 degrees Max. load C-axis 100kg Table diameter C-Axis d290mm Rotary joint, 4-channels Inclusive So
Rotary joint, 6 channels Rotary lead through for integrated swivel rotary table with torque drives 6- flute, 2x for air, 4x for oil Including fix plate and fast coupling at machine side
Tool magazine 25 places Tool magazine 25 places (suitable for inclusion in the tool spindle) Max. tool length 150 mm Chip-to-chip time 1.6 sec Note: machine width increases to 1410 mm!
Production package band filter ICS 40bar Paper band filter ICS 40bar includes: Paper band filter 40bar/ 23l/min Additional tank 600l Chip conveyor useable for fine chips (self cleaning slotted filter) Discharge height: 600mm; Tank volume 200l Flushing in working room Spray gun for swarf removal
Air blast through spindle centre Air blast through spindle center via M-Command; maintained air with small Oil portion Due to needed lead through in main spindle only with swarf removal package ICS possible!
RENISHAW touch probe-Kit RENISHAW measuring suitable to tool taper System in Spindle OMP40-2 touch probe with optical signal transmission OTS wireless probe with air purge on machine table OMI-2T optical transmission module Plastic carrying case Calibration tool incl. tool holder
Preparation 3D Quickset Machine preparation for use of the 3D quickSET Toolkit. included is the Softwareoption for 3D quickSET for one machine. 5 axis machine configurations (only with option touch probe)
proTIME proTIME Visualisation of remaining runtime, remaining workpieces and the machine state
Signal lamp 4-colour Signal lamp, 4 colours
Automation Interface WH CELL right Automation interface right for WH CELL / WH FLEX Interface (Profibus) via M65; Automatic loading door right; Working table with 4-channel rotary joint; 4-chanel enegry supply to machine table for (3-Axis-Machines); Only in combination with an additional c
Price reduction for automation from DMG MORI Price reduction on automation interface with simultaneous order of a DMG MORI Automation solution
Operation mode 4 Operation mode 4 Process monitoring in the production Manual intervention with open doors of machining area. Release after check list has been filled in.
Digital Manufacturing Package Digital Manufacturing Package (1) IoTconnector Allows the use of the Online services from DMG MORI (2) Machine Data Connector (MDC) Standardized machine data interface Protocols: OPCUA, MTConnect, MQTT (3) NETservice Qualified support through internet-b
Messenger V4 The latest version of DMG MORI Messenger displays web based the machine live status. It allows to analyze the machine run-time, downtime, alarms in individually configurable dashboards and transparently shows the actual status in the manufacturing shop
Workpiece loading & unloading system WH 3 CELL Workpiece loading & unloading system WH 3 CELL with 6-axis industrial robots and workpiece carrier storing system (paternoster); maximum possible workpiece weight of 3 kg, maximum workpiece size 100 x 100 x 50 mm Robot FANUC LR Mate 200 iD/7L D5952871 PROFIBUS D5952871 in
Pneumatic pallet pusher - robot side Pneumatic cylinder installed on the robot side for slide over individual workpiece pallets within the paternoster system.
Menu-driven input programming Menu-driven input programming Control extension in addition to the Teach programming; Process definition by entering parameters; Separate intuitive user interface;
Robot FANUC LR Mate 200 iD/14L Robot FANUC LR Mate 200 iD/14L for Load capacity extension up to 14 kg transfer weight (deviating axis speeds to robot FANUC LR Mate 200 iD/7L!)
WH 3 CELL Integration kit for DMP 35/70 WH 3 CELL Integration kit for DMP 35/70 Machine-specific adaptation for the protective housing on one DMP 35/70
Dual gripper PGN 80 (without gripper fingers) Dual gripper Type Schunk PGN 80 with 8 mm travel per jaw (gripper fingers not included!)
Gripper quick-change system 2 gripper Gripper quick-change system for dual gripper
Workpiece carrier standard Workpiece carrier standard - plastic 15 Workpiece carrier 600x400 (workpiece specified inlay´s not include)
SPC drawer SPC drawer (only to be removed) Output of a trial workpiece for process control
Turning station (without gripper fingers) Turning station includes 1 gripper, type depending on the selection and rotary module 0° / 180° (gripper fingers not included!)
Alignment station Alignment station for exact positioning of the workpiece in the gripper.
Robot Teachset Robot Teachset for the new creation of workpieces / workpiece carriers as well as for the basic adjustment of the robot and / or gripper.
Not OK discharge via slide Not OK discharge via slide Removal of bad parts after machine signal
Special equipment 1 set of gripper jaws for turning station Design analogous to gripper jaw set PGN+80 2 sets of gripper fingers for gripper unit Design analogous to gripper jaw set PGN+80, suitable for gripper unit and quick-change gripper finger system 1 piece workpiec

seller offer No. resale 051095
Condividi questa macchina su Facebook:
aggiungi alla lista selezionati
rivenditore
autorizzato

Venditore

logo dealer

DMG MORI Used Machines GmbH

Signora Kerstin Bauer
82538 Geretsried
Germany

RESALE membro dato che 2019


verified user
[ profilo del rivenditore ]
  • elenco macchine (212)
invia la richiesta
invia la richiesta

Inchiesta

Commerciante di macchine?

Si prega di rimettere in opzione

Inviare la domanda desiderato?

(a tutti i concessionari per una tale macchina)

Copia a voi?

(copia della richiesta sarà inviata al vostro indirizzo email)

Save input data

(Save input data for further inquiries)

di più DMG MORI DMP 35 + similar DMG MORI-Modello

DMG MORIDMP 35
DMG MORICTX 350
DMG MORICTX 350
DMG MORICTX 350
DMG MORICTX 350
DMG MORICTX 350
DMG MORICTX 350
DMG MORICLX 350
DMG MORICTX 350
2019 DMG MORICLX 350 V6

Prezzo: sold DMG MORI DMP 35 + simili DMG MORI-Modello

2017 DMG MORICLX 350 57620 EUR [Jul 2023]
2017 DMG MORICLX 350 72620 EUR [May 2024]
2017 DMG MORICLX 350 72620 EUR [May 2024]
2017 DMG MORICLX 350 V3 75000 EUR [Aug 2019]