macchine per gomma usati in vendita (406)

Tssen Krupp modello GK270NC Banbury tipo mixer interno, rotori tangenziali a 4 ali, Anno di fabbricazione: 2003 Ultima camera di progettazione Continental! Tramoggia idraulica - power pack. Corpo e tramoggia solo in buone condizioni. Cambio unidrive e motore può essere citato per se necessario (stessi centri come 11D o F270).

Farrel Pomini Modello OOC Lab Banbury Mixer Interno numero macchina: 7511, Anno: 1976 Volume netto: 4,24 litri tramoggia pneumatica Motore a velocità variabile DC da 30 kW. Completo di pannello di controllo ecc e in ottime condizioni.

Francis Shaw 18/22- Estrusore di scarico, Alimentazione Crammer Lunghezza della vite 9ft 6. Affidabile 400hp D.C., 1150 r.p.m., 480 volt. Grande Hopper/Chute al livello del piano successivo.

Unità di estrusione Duplex Doppio estrusore di tipo PIN da 150 mm, Anno di fabbricazione: 1990, con Roller Feed, e duplex Die. Rapporto L/D 16:1 Numero di Pin: 10 Righe x 8 Pezzi, Perni di ricambio inclusi. Vite Velocità 45 r.p.m. Motori 185kw D.C. velocità variabile, 415 volt, 3ph, 50hz. Libri completi e disegni disponibili. Unità Thyristor incluse. Starter e Pannello di controllo solo per Estrusore inferiore. Muori di larghezza utilizzabile 18, in buone condizioni.

1 x David Bridge 15/18- Estrusore di dump con 40. Pezzi di ricambio disponibili. Vite L/D 5:1, Crammer. Lunghezza della canna di 7 piedi. Unità di tornitura ad angolo retto per il flusso del prodotto. Motore a velocità variabile DC da 200 CV

Kobelco Twin Screw Roller Head Estrusore (tipo orizzontale), Modello TSR-330 Assemblaggio a rulli (TSR-33H005H) 38in larghezza x 16in dia Il dadi a rullo si allontana dalla sezione estrusore/mixer tramite ariete idrauliche. guidato da 102kW DC motore a velocità variabile attraverso Hansen cambio di riduzione (su accoppiamento flessibile in modo da die rullo può andare avanti / indietro). Estrusore a vite doppia Dia a vite 330mm motore a velocità variabile da 90 kW DC attraverso il cambio di riduzione Hanson. In ottime condizioni. Precedentemente in esecuzione sotto un F270 Banbury. Completo di tutti i controlli, manuali e documentazione, ecc.

Farrel Pomini modello F620 Banbury miscelatore interno, volume della camera di miscelazione netta: 710 litri Numero macchina 6515. Anno di fabbricazione originale: 1972, ma corpo sostituito 1998 circa il peso del lotto a SG 1 - 533kg, 4 rotori alari, lati forati, camera saldata completamente stellita, rotori e peso galleggiante, Sigilli alla polvere S.S.A., porta di caduta idraulica con attuatore lineare, tramoggia pneumatica, cambio unidrive con 2 motori a velocità variabile CEM 1475kW, 1550A, 1000V, 800/1000 rpm DC, Controlli dell'azionamento inclusi, ma i controlli dell'operatore non sono disponibili. In buone condizioni (utilizzato solo per il masterbatch composto pneumatico). Spare disponibili: Piano porta (nuovo), albero della cerniera (nuovo), 2 x guarnizioni di polvere, guarnizioni tramoggia e guarnizioni per cuscinetti.

Troester 150mm dia PIN estrusore Tipo: QSM150K, Numero di serie 8622/80, Anno di fabbricazione: 1980, ma ristrutturato da Troester 2000 (nuova sezione vite e botte) Alimentazione a rulli di potenza, Rapporto L/D 16:1 8 file di 8 pin, con motore e comandi a velocità variabile ASEA a 212 kW DC (1800 giri/min). Completo di controlli ecc e in ottime condizioni.

Linea a rulli composta da:- 1 x Estrusore troester 200mm Tipo QSM200K-16D alimentazione a rulli di alimentazione, 10 file di 8 pin, Rapporto L/D 16:1 Numero di serie 1816/88, anno 1988, Con l'unità di regolazione della temperatura, Motore a velocità variabile ASEA DC da 282 kW DC montata su rotaie (si sposta dal calendario per pulire, ecc.) Teste di lamiera idraulica collegate direttamente a:- 1 x Adamson 24in dia x 68in ampio due rotoli, rotoli periferici asse trasversale, cuscinetti di tipo cespuglio, regolazione del nip motorizzato con cambio unidrive Motore a velocità variabile 277kW ASEA DC Dispositivo di bloccaggio idraulico per estrusore Set di tamburi di raffreddamento 4 x Applicatore a doppia vento verso l'alto e fodera Unità di Gesso Controllo Siemens PLC. Linea completa in ottime condizioni. PRICE: Su richiesta.

1 x Francis Shaw Modello K6 Intermix, Anno di fabbricazione originale: 1977, Carrozzeria ricostruita montata dalla Carter n. 242.93, Anno: 1993, Scarico della porta di caduta idraulica, Volume della camera di miscelazione: Circa 112 litri Tramoggia pneumatica, 750HP, motore slip ring, 3ph, 50 Hz a Sturdigear 1460/15.7 rpm cambio di riduzione (1000HP valutazione). Completo di unità idraulica - controlli dell'operatore ecc e in ottime condizioni.

machine measurements: -- mmmachine weight: -- kgpower capacity: -- kWCondition: used, Specification: drum-type blast deburring machine type: MEWO Rotor TS 60- batch volume approx.: 1-100 litres,- working temperature: - 150°C- drum speed: 5 - 30 rpm- Blast wheel speed: 1,000 - 9,500 rpm- Control: Siemens S7 SimaticThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll diameter: 500 mmroll length: 1500 mmrolls drilled: Kernbohrung Nip adjustment: hydraulisch 0total power requirement: 110 kWCondition: used, overhauled Specification: Rolling mill 500 x 1500 mm - second-hand- roller diameter: 500 mm- roll length: 1500 mm- monoblock motor under the rollers- Fixed friction between the rollers- Rollers: with core bore, with central chamber for water cooling- Gap adjustments: NEW hydraulic- Hydraulic unit: NEW- Tilting material guide jaws made of steel with mechanical with mechanical safety interlock- Rollers: mounted on bronze bushes with circulating oil lubrication via pump- New Johnson-Fluiten ball swivel joints for connection to water circuit to water circuit- New safety brake for EMERGENCY STOP- New AC moto ...

roll diameter: 250 mmroll length: 500 mmrolls drilled: Kernbohrung nip adjustment: mechanisch drive power:: kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

machine measurements: 3.000 mmmachine weight: -- kgpower capacity: 90 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll diameter: 700 mmroll length: 2200 mmrolls drilled: Kernbohrung Nip adjustment: hyraulisch 0total power requirement: 160 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Press force max.:: 3000 kNheating plates:: 600 x 630 mmelectrically heated:: °Cheating power:: kWpiston stroke:: 420 mmno. of stages:: 1 Condition: Used, reconditionedSpecification: Press 600 x 630 mm, second-hand- clamping force: 300 tonnes (3,000 kN)- closing: from bottom to top- Heating platens: 2 electric platens, with new heating rods- Heating platen dimensions approx.: 600 x 630 mm- Distance between the heating platens approx.: 420 mm- New electric valves- AC machine output oil pump: 5.5 kW- New control cabinet with Siemens 7’ touch panel- PLC control system make Siemens S7-1200- New cabling- Frequency inverter made by Schneider- Light barriers in the front area,Overhauled in accordance with CE standard safety regulationsOperating instructions and maintenance instructions in GermanWarranty: 1 yearThe data for this ad was created with ModulMWS - the sof ...

0: 200 °CTorque: - 0Dimensions (HxWxD): 680 x 1320 x 760 mmweight: 177 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

machine measurements: 1500 x 2400 x 1150 mmmachine weight: -- kgpower capacity: 12 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

screw ø:: 70 mmscrew length:: 22D screw speedl:: -- U/minCondition: usedSpecification: rubber extruder line – used COLMEC Extruder, Hot Air Channel, Cooling BathConsisting of:Extruder COLMEC 70 x 22D- Screw diameter: 70 mm- Screw length approx.: 22D- Extruder motor power: 37 kW- Cooling unit for extruderHot air oven:- Hot air oven power: 80 kW- Fan power: 2x 0.36 kW, 2x 1.5 kW- Stainless steel cooling bathThe system is in good condition and wasstill in operation until approx. 6 months ago- Sold as seen. The buyer is responsible for safety regulations. Without CE markingThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll diameter: 550 mmroll length: 1500 mmrolls drilled: peripher Nip adjustment: hydraulisch 0total power requirement: 110 kWCondition: used, overhauled Specification: rolling mill 550 x 1500 mm - used- roll diameter: 550 mm- roll length: 1500 mm- monoblock - motor under the rolls- Fixed friction between the rolls- Rolls: peripherally drilled, for water cooling- Gap adjustments: NEW hydraulic- Hydraulic unit: NEW- tiltable steel material guide jaws- Rollers: mounted on bronze bushes with oil circulation lubrication via pump- new ball bearing slewing rings for connection to water circuit- Safety brake for EMERGENCY STOP- New AC motor 110 kW - 400 V - 50 Hz - New pan for receiving the mixture- Safety bars bi-directional- New electrical control cabinet with PLC system S7-120 ...

screw ø:: 60 mmscrew length:: 11D screw speedl:: -- U/mindrive power:: 18,5 kWCondition: used, reconditionedSpecification: rubber extruder – used- Screw diameter: 60 mm- Screw length approx.: 11D- New screw- Cylinder refurbishment- Feed roller refurbishment- New safety cage- New rotary joint for water- New AC motor: 18.5 kW- New control cabinet with Siemens S7-1200 PLC system- New control panel with Siemens KTP700 Basic touch panel- New Siemens G120 frequency converter for variable speed- Remote maintenance device- New cabling- Pressure sensors on the extruder head- Safety device- CE marking and an operating and maintenance manual in EnglishRefurbished in accordance with CE standard safety regulationsWarranty: 1 yearOption: TCU for temperature control of the water up to 95°C, for placement near the extruderThe data for thi ...

clamping force: 2.700 kNinjection volume: 6.000 cm³screw diameter: -- mmplaten size: 560 x 630 mmCondition: second-hand,Specification: rubber injection moulding machine - second-hand, partially dismantled, but would be restored to its previous condition EUROMAP size 2500 – 7000Clamping unit:- Clamping unit: vertical- Clamping force: 2.700 kN- Platen size: 560 x 630 mm- Max. stroke: 550 mm (see data sheet) Injection unit:- Max. injection volume: 6,000 cm³- Injection pressure: 2150 bar- Power supply: 3x 400 V, 50 Hz, N, PE- Motor power: 28,2 kW- Installed heating capacity: 49,9 kW- Weight: Clamping unit approx.: 6,040 kg Injection unit approx.: 2,700 kg Hydraulic un ...

clamping force: 4.500 kNinjection volume: 3.300 cm³screw diameter: -- mmplaten size: 670 x 780 mmCondition: second-hand,Specification: rubber injection moulding machine - second-hand EUROMAP size 4000 – 7000Clamping unit:- Clamping unit: vertical- Clamping force: 4500 kN- Platen size: 670 x 780 mm- Max. stroke: 600 mm (see data sheet) Injection unit:- Max. injection volume: 3,300 cm³- Injection pressure: 2150 bar- Power supply: 3x 400 V, 50 Hz, N- Motor power: 35,5 kW- Installed heating capacity: 73,9 kW- Weight: Clamping unit approx.: 8,400 kg Injection unit approx.: 2,700 kg Hydraulic unit with oil and control cabinet 2,200 kg Additional equipment (approx.): 3,000 kg  ...

clamping force: 4.500 kNinjection volume: 5.600 cm³screw diameter: 610 - 985 mmplaten size: 670 x 780 mmCondition: second-hand,Specification: rubber injection moulding machine - second-hand EUROMAP size 4500 – 12300Clamping unit:- Clamping unit: vertical- Clamping force: 4500 kN- Platen size: 670 x 780 mm- Max. stroke: 610 - 985 mm (see data sheet) Injection unit:- Injection unit type: ADV- Max. injection volume: 5,600 cm³- Injection pressure: 2200 bar- Power supply: 3x 400 V, 50 Hz, N, PE- Pump capacity: 27 kW- Weight: Cutting unit approx.: 10,200 kg Injection unit approx.: 3,500 kg Hydraulic unit with oil: 2,600 kg Accessories approx.: 4,700 kg Total weight approx.:  ...

clamping force: 4.500 kNinjection volume: 5.000 cm³screw diameter: -- mmplaten size: 670 x 780 mmCondition: second-hand,Specification: rubber injection moulding machine - second-hand EUROMAP size 4500 – 10000Clamping unit:- Clamping unit: vertical- Clamping force: 4500 kN- Platen size: 670 x 780 mm- Max. stroke: 600 mm (see data sheet) Injection unit:- Max. injection volume: 5,000 cm³- Injection pressure: 2060 bar- Power supply: 3x 400 V, 50 Hz, N, PE- Motor power: 38 kW- Installed heating capacity: 67.5 kW- Weight:Clamping unit approx.: 8,900 kgInjection unit approx.: 3,200 kgHydraulic unit with oiland control cabinet 2,350 kg- For dimensions, see the installation data in the appe ...

clamping force: 300 kNinjection volume: 180 cm³screw diameter: -- mmplaten size: 300 x 300 mmCondition: second-hand,Specification: C-frame injection moulding machine for rubber - second-handClamping unit:- Clamping unit: vertical- Clamping force: 300 kN- Platen size: 300 x 300 mm Injection unit:- Maximum injection volume: 180 cm³- Mains supply: 3x 400 V, 50 Hz- Power rating: 11 kW- Control system: MAPLANThe machine is still in production and can be viewedin operation.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll surface width: 450 mmroll diam. toproll: 203 mmroll diam. bottom roll: 203 mmoutput: 8,8 kwSmall roll gap 0.1 mmMaximum roll gap 47 mmFront/rear roll speed 5-30 rpmFront/rear roll speed 3.2-19.1 m/minRolls individually drivenFriction variable max. 1:6Manual gap adjustmentManual speed controlExternal temperature controlRollers internally cooled (water cooling)Emergency stop handle (manual operation) on both sidesThe tech. Data are manufacturer or operator information and therefore non-binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively.About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours ...

speed of feed:: 60 m/minfeed:: 5 - 99.999,9 mmcuts max.:: -- Schnitte/mcross-section width:: 5 - 90 mmcross-section heigth:: 5 - 90 mmCondition: Second-hand,Specification: Strip and tube cutting unit • Cutting unit: Impact blade cutting with cutting sleeves• Material diameter approx.: 5–90 mm• Conveyed by two drive belts• Distance between the belts max.: 90 mm • Belt adjustment via motor, controlled via control panel• Lower belt fixed, upper belt motor-adjustable• Belt contact length approx.: 500 mm• Contact width: 80 mm• With a maximum speed of approx.: 60 m/min• Electronic length measurement: 5 – 99,999.9 mm • Maximum cutting accuracy: +/- 2 mm• Cutting is performed by a servo motor: 1 kW• Power supply: 380/400V, 50Hz, 5kW• Material feed directio ...

volt: 380 Vweight: 1,4 t: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 350 kNinjection volume: 170 cm³screw diameter: 36 mmplaten size: 380 x 300 mmCondition: second-hand,Specification: C-frame injection moulding machine - second-handClamping unit:- Clamping force: 350 kN- Platen size: 380 x 300 mm- Heating power of the plates: 6 kW- Clamping/opening stroke: 200 mm- Clearance between the plates: 250 mm- Clamping direction: from belowInjection unit:- Pressure: 1,050 kg/cm²- Maximum injection volume: 134 cm³- Screw diameter: 35 mm- Max. screw speed: 30–110 rpm- Metering stroke: 165 mm- Injection: from above- Voltage: 3 × 400 V, 50 Hz, N, PE- Pump drive power: 11 kW- Hydraulic motor power: 10 kW- Dimensions LxWxH: 2,400 x 1,200 x 3,300 mm- Weight ap ...