altre macchine per lavorazione del legno usati in vendita

Spessore del pezzo: 8 - 50 mmSpessore del bordo: Bordi della bobina 0,4 - 3 mmVelocità di avanzamento 10 m/minAttrezzatura: regolazione manuale dell'altezza. Unità di fresatura per giunti, 2 motori Riscaldamento del bordo del pannelloArea di incollaggio Zona di pressione 1 rulli motorizzati e 2 non motorizzatiProfili terminali, 2 motori da 0,8 kW, diritti e smussi 15Rifilatura superiore e inferioreUnità raschiante per bordi in PVCRASCHIATORI di colla

Min./max. thickness edge banding on roll: 0,4 - 3mmMin./max. thickness edge banding in strips: 5 mmMin./max. panel thickness: 8 - 50mmMin. panel length/width: 190/110mmThroughput speed: 9m/minPre-milling unit: 2,2kW 7200 rpmSprayers release agentPanel heating device Automatic laoding for edgesGluing unit: 0,18kWEnd-cutting unit with radius: 0,19kWTrimming unit: 2x 0,35kW, 12000rpmRounding unit up to 3mm: 0,35kWEdge scraping unitSprayers cleaning agentGlue scraping unitBrushing unit

Regolazione motorizzata dell'altezzaInvolucro acustico su tutti i motori di rifilaturaEquipaggiamento:Magazzino bobine e nastriUnità hot melt Zona di pressione Rifilatura terminale, smusso e dritto, regolazione automaticaRifilatura di sgrossatura superiore/inferioreRifilatura di sgrossatura superiore/inferiore, inclinazione, Unità di rifilatura dei contorniUnità di raschiaturaUnità di smerigliaturaTrasportatore di ritorno Ligmatech ZHR 05

Fixed side at the leftFeedspeed 18 - 25 m/minWorking width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mmPanel overhang 30mmPanel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations)Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mmCoil diameter 830 mmEquipment:Sprayers release agentSquaring device with 2 motors each 3 kWEdge heatingEdge magazine for 2 coils, guillotine for edges up to 3 mmGlueing part A20 with quickmelt applicationLateral pressure zone K, 1 driven and 6 after pressing rollersEnd trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kWContour trimming, 2 exchange unitsProfile scraping PN10Flat scrapers FA11Sprayers cleaning agentBuffingAutomation package straight/chamfer:-Automatic adjustment infeed fence-Automatic setting of pressure rollers-Pneumatic setting of end trims-Pneumatic setting of rough trims-Automatic setting of chamfer/ra ...

Single sided edge bander with hot melt, fixed side at the right, pre-milling unitEdge thickness: 0,4 to 12 mmWorkpiece thickness: 8 - 60 mmFeedspeed 8-20 m/min (limited to 10 m/min using the contour trimming)Workpiece transport by chain, top pressures with rubber rollersSound enclosure over all trimming motorsEquipment:Adjustable fencePre-milling with 2 shapers, each 2,2 kWCoil and strip magazine Hot melt unit, Quickmelt type Pressure zone with1 driven and 2 non-driven pneum. Loaded rollersEnd trims, 2 x 0,35 kW motors, straight and chamfer 15°Top/bottom trimming, motors 2 x 0,35 kWRadius trimmmingContour trimming unit, leading and following edge, 2 x 0,35 kWRadius scraping unitGlue scrapersBuffing unitControlls PC 20+

Workpiece thickness: 8 - 90 mm, electronically adjustableFeed rate: 18-32 m/min frequency controlledEdge thickness: 0.3 - 3 mm for roll edges, strips up to 20 mmEquipment:Inlet guide automatically adjustable via the control, extension 500 mmJoint milling unit: 2 x 3.0 KWworkpiece preheatingGluing unit A34edging magazine for rollPressure zone with 1 driven, 6 non-driven rollers, automatic adjustment from the controlCutting unit WK14, straight, 2 motors 0.8 kWPre-milling unit: 2 x 1.5 KW, pneumatic adjustmentForm milling unit FF 12 automatic, 2 motors 0.4 kWradius/phase milling unit FF12 automatic 4 motors 0.4 KWuniversal milling aggregate controlled UF11, 4 kWProfile scrapers PN20Glue scrapersNozzles for detergent and anti-stickPolishing unitControl: Power Control PC22

Fixed side at the leftFeedspeed 18 - 25 m/minWorking width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mmPanel overhang 30mmPanel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations)Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mmCoil diameter 830 mmEquipment:Sprayers release agentSquaring device with 2 motors each 3 kWEdge heatingEdge magazine for 2 coils, guillotine for edges up to 3 mmGlueing part A20 with quickmelt applicationLateral pressure zone K, 1 driven and 6 after pressing rollersEnd trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kWContour trimming, 2 exchange unitsProfile scraping PN10Flat scrapers FA11Sprayers cleaning agentBuffingAutomation package straight/chamfer:-Automatic adjustment infeed fence-Automatic setting of pressure rollers-Pneumatic setting of end trims-Pneumatic setting of rough trims-Automatic setting of chamfer/ra ...

Fixed side at the leftPanel thickness min/max: 16/45 mmMin. panel width: 150 mmLateral panel support for panel width up to 900 mmMin/max. panel length: 700 / 3100 mmMax. laminate overhang: 110 mmMax. laminate thickness: 0,8 mmRadius min/max: 6 / 22 mm (depends the laminate)Feedspeed max. 18 m/minTop pressure by beltEquipment:Infeed fence, adjustable, defines the panel overhang2 x trimming unit 0,4 kW, HSK 25 toolholder1 x PVAc glue application5 x glue nozzle, adjustable1 x hot air blower3 x IR heating on top (55 cm length), 3 x bottom (90 cm length)Postforming zone 1,8 m. lengthVarious pre-installed profiling sets 1 x top trimmer 0,4 kW

Panel thickness: 12 - 60 mmFeed speed: 18 m/minEdge thickness: 0,3 - 3 mm for coil edgesEquipment: Programmable fence at the infeedSquaring device: 2 x 3,0 KWGlue application unit: A34 double edge magazine for 2 coils Lateral pressure rollers, thickness programmable, 1 driven, 2 non-driven rollersEnd trims HL84/85, programmable change straight/chamfer, 2 motors 0,18 kWRough trimming: 2 x 0,55 KWContour trimming FK 13, 2 x 0,55 KWProfile scrapers PN10Flat scrapersBuffing unitControlls: HOMATIC NC21

Single sided postforming line, capable of doing L - and U profiles, with or without insert.Workpiece thickness: 16 to 60 mm.Min. workpiece width: 150 mm.Workpiece overhang: 70 mm.Max. laminate overhang: 105 mm.Feed speed 3 - 18 m/min.Fence side at the leftEquipment:Squaring and shaping part:1 x Postforming squaring unit, 2 motors each 1kW, 1st motor removing the laminate, 2nd motor trimming the overhaning laminate1 x scoring, motor 1 kW, top position1 x milling unit for the laminate when doing U profiles 1 x laminate support Postforming part1 x blow cleaning nozzle 6 x glue nozzle for the glue application 2 x glue roller9 x IR heating, each 2,2 kW2 x Hot air blower, each 10 kW1 x Basic postforming pressure zone for L-profiles, using rollers1 x Basic postforming pressure zone for U-profiles, using rollers1 x VF postforming pressure zone for special profiles, using pressure pathsFinishing  ...

Workpiece thickness: 12 - 60 mmFeed speed: 18 - 24 m/minEdge thickness: 0.4 - 6 mm for roll edges, 0.4 - 20 mm for stripsEquipment:manual fence at the infeedworkpiece preheatingBonding unit: QA34 / A20edge magazinePressure zone with 1 driven, 6 non-driven rollers, automatic adjustment from the controlHood unit HL83, automatic adjustment phase/straight, 2 motors 0.4 kWPre-milling unit: 2 x 1.5 KWMilling unit, with sensing, tiltable, 0.4 kWMold milling unit FF 12, 4-way tool changer, 4 motors 0.4 kWuniversal milling unitprofile sanding unitedge sanding unitControl: HOMATIC NC21

Bordatrice con azionamento manuale e applicazione di colla a caldo per pannelli sagomati Spessore del pannello: da 10 a 40 mm Spessore del bordo: 0,5 - 1 mm Velocità di avanzamento: circa 4 m/minSolo bordi della bobina

La bordatrice a controllo numerico serve per bordare pannelli curvi e sagomatiDiametro del pannello: 16 - 50 mm.Spessore del bordo: 0,8 - 3 mm.Dimensioni: min 400 x 400 mm, max 1800 x 1800 mm 650 x 2500 mmunità 1: rullo colla con caricatore bobina bordoVasca colla con capacità di 3 l. Unità 2: motore di rifilatura di finituramotore 0,8kWUnit 3: Motore di rifilatura 2 x 2,2kW

Panel thickness: 12 - 60 mmFeed speed: 18 - 24 m/minEdge thickness: 0,4 - 3 mm for coil edges, 0,4 - 20 mm for strips / solid woodEquipment: Help carriage feeding the panels rectangularautomatic fence at the infeedSquaring device: 2 x 3,0 KWPanel edge pre-heaterHot melt unit: QA34 / A20 edge magazine Lateral pressure rollers, thickness programmable, 1 driven, 6 non-driven rollersEnd trims HL83, programmable change straight/chamfer, 2 motors 0,5 kWRough trimming: 2 x 1,5 KWTop/bottom fine trimming, tilting, 2 x 0,4 kWContour trimming FK 13, 2 x 0,4 KW, with 8-fold toolchangersUniversal milling motor 4kW Profile scrapersFlat scrapersBuffing unit with oscillationControlls: HOMATIC NC16

Working field: axis x: 2310 mm, axis y: 628 mm, axis z: 90mmMax programmable speed: axis x: 100 m/min, axis y: 75 m/min, axis z: 15 m/minDrill chuck: diameter 10 mmSpindle speeds: 4000 rpmGrooving saw: diameter 120 mmDrill spindles: 4 horizontal spindles in X,12vertical spindles in X lineWorking air pressure: 6 barMax consumption of compressed air: 0,75 NL/cycleInstalled power: max 7.5 kWCapacity of vacuum tools: 40 m³/hCNC:screen: monochromatic 9”Floppy disk unitPLC for control of the machine cycle

Campo di lavoro: asse x: 3200 mm, asse y: 944 mm, asse z: 110 mmVelocità massima programmabile: asse x: 100 m/min, asse y: 75 m/min, asse z: 15 m/minPortatrapano: diametro 10 mmVelocità del mandrino: 4000 giri/minSega per scanalatura: diametro 120 mmMandrini per trapano: 24 mandrini orizzontali in X, 10 mandrini verticali in linea XPressione di lavoro dell'aria: 6 barPotenza installata: max 25 kWCacità degli utensili ad aspirazione: 40 m³/hCNC:schermo: monocromatico 9"Unità floppy disk

X=3700mm Y=1440mm, Z=150mmMoving speed: X: 80 m/min, Y: 80 m/min, Z: 20 m/min8 supports with vacuum cups, pneumatic clamping8 fences at the rear8 fences in front2 left fences and 2 right fences6 rails for panel loading with pneumatic liftingPositioning the vacuum cups using a laser1 connection for templatesVacuum pump with flow rate 100 m3/hConfiguration V25,H8X/6Y, N1 X-Y 90°, F1-HSK63-15KW,F1-HSK63-9KW, C axis, W14 rearMain motor 15 kW, 1250-24000 rpm, air-cooled, 360° C-axis, C-axis interpolation axis, HSK 63 mountingC axis extension for flex-5 aggregateMain motor 9 kW, 1250-24000 rpm, air cooled, HSK 63 mountingTool changer operating in X direction with 14 positions, rear mounted2 x 4 vertical X drilling pins, 2 x 3 vertical Y drilling pins14 horizontal drilling spindles90° groove saw X-Y directionPC 85 power control software with:Woodwop: workshop-oriented programming systemImpor ...

Area di lavoro: X 5200 x Y 1260 mmIntestazione del mandrino principale: X 5709 mm, Y 1650 mm8 mensole portapezziAttrezzatura:Unità di foratura con 18 mandrini, 12 punte verticali, 6 mandrini orizzontali (4 in direzione X, 2 in direzione Y)Sega per scanalatureMotore di fresatura 11 kW, 20000 giri/min max, avvolgimento HSK-F 63, raffreddato a liquido, controllato a 5 assiCambio utensile con 16 posizioniCambio a posizione laterale con 8 posizioni Controllo PC

Workpiece sizes: Length 180 - 2500 mm, width 150 - 800 mm, thickness 12 - 40 mmFixed side at the left, motorised width adjustment of the right side Working height/ transport height: 920 mmWorkpiecetransport with belts, infeed belts can lift upVariable feed speedEach side has got 5 glue injectors and 8 dowel inserters (Type 34)Doweldiameter: 8 mm, dowellength 30 mm, dowelprojection 7-14 mm, dowelcenters min. 32 mm, max. 736 mmEach side with dowel hopper feed with shaker and separatorsControll mirrorGlue pump 1:1 Glue injection controlls type ELC

Machine designed for machining solid wood doors with frame and raised panelsWorkpiece dimensions Length 150 - 3000 mm Width 40 - 300 mm Thickness 20 - 60 mm Material: hard woods/soft woods Machine equiped with 2 working areas, including - 3 NC-axes X, Y, Z- telephone modem- 1 sawing unit- 1 horizontal boring unit- distance horizontal drill above table (Z):max. 40 mm- fixed workpiece table- central lubrication- CE package- max. workpiece length 2.400 mm KOCH Numeric with 3 NC-axes Positioning control with PC Pentium CPU Operating system Windows XP Professional: english 15” Touchpanel VGA + Touchscreen by means of LVDS connection USB-connection on PC and on Touchpanel Seriel and parallel interface on the PC Hard disk 2,5 Input of machine commands and motor control through the Touchpanel PS2 connection for external keyboard Office PC software Stretched machine bas for max. workpiece widt ...

Machine for cutting, milling, drilling and dowelling frames or rails, straight or mitre, with or without counter profiles in small batch size or one-off productionWorkpiece length 160 - 2350 mm.Workpiece width:- 20 - 140 mm for 2 workpieces per field- 20 - 100 mm for 2 workpieces per field at 45 °- 20 - 300 mm for 1 workpiece per fieldWorkpiece thickness 10 - 30 mm.Angle adjustable between 45 ° and 90 °Tables can be tilted 25 °PC controlled on 3 axesDrilling and inserting on point-to-point basisEquipment:Sawing station: saw blade 350 x 30 mm, motor 2.2 kW, 2800 R / minDrilling station: drill bit diameter 10 mm, motor 2 kWMilling station: diameter tool 100 - 200 mm, spindle diameter 40 mm, clamping length 70 mm, motor 3 kW, 6000 - 12000 R / minDowelling station: dowel dimensions 8 x 30 mm, 8 x 20 mm

larghezza massima del pezzo: 2500 mmspessore massimo: 150 mmAvanzamento tramite binario a catenaPressione superiore tramite cinghieAttrezzatura:1+1 Motore sega 7,5 kW

Working width 180 - 3200 mm, electronic setting Sieb & MeyerFixed side at the leftChain transport, 80 mm wideInfeed for panels of about 1 m.Top pressure by driven beltsMax. workpiece thickness: 80 mmFeedspeed 7 - 35 m/min, motor 4 kWPop-up dogs every 1m10Equipment left / right:1 st postFront: 1+1 Jump scorer, motor 1,5 kW, 100 Hz, joined to 1+1 Hogger, motor 2,2 / 3,3 kW, 50/100 HzRear: 1+1 Jump milling, tilting, motor 1,5 kW, 100 Hz2nd postFront: 1+1 Jump milling, tilting, motor 1,5 kW, 100 HzRear: 1+1 Fixed milling, tilting, motor 2,2/3,3 kW, 50/100 Hz3th postFront: 1+0 Jump milling, tilting, motor 2,2/3,3 kW, 50/100 HzRear: 1+1 Jump milling, tilting, motor 1,5 kW, 100 HzAll units with horizontal/vertical adjustment and Siko read-outOutfeed chain approx. 80 cm lengthSound and safety enclosures

Versione destraTroncatrice: 1,5 kW2 x albero orizzontale: 2 x 1,5 kW1 x albero verticale, diametro 50 mm, lunghezza 160 mm, 2,2 kW

Numero inv. : 8465 Tipo: SP-300x4C Produttore: Prochera Creato: 2015 Parametri: Velocità massima: 1500 1/min Avanzamento di lavoro: 0-23 m/min Larghezza massima: 300 mm Altezza massima: 100 mm Numero di spazzole: 4 Peso: 1500 kg Attrezzatura: Spazzole di ricambio

Numero inv. : 8415 Tipo: S 200 Produttore: Opticut Creato: 2006 Parametri: Area di taglio: 260 x 12 mm Lunghezza massima: 6300 mm

Numero Inv. : 8372 Tipo: ZLSM-4x1.20-3x1.20-0 Produttore: Mühlböck Generato: Parametri: Profondità: 5400 mm Altezza: 4200 mm Lunghezza: 6520 mm Capacità: 12 x 8 63 m3 (103 68 m3) Carico: 100 kg per 1m2 Numero di ventilatori: 4 pezzi

Questa bordatrice BRANDT KDF 650 Highflex 1650 è stata prodotta nel 2013. Ideale per applicazioni di bordatura precisa, garantisce prestazioni affidabili per i professionisti della lavorazione del legno. Considera l'opportunità di acquistare questa bordatrice BRANDT KDF 650 Highflex 1650. Contattaci per maggiori informazioni.

Vendo un essiccatore Kovos SR 4 smontato senza elettronica. Senza isolamento termico (lana di vetro) 2x ventilatori, 2x serpentine di riscaldamento. Dimensioni dell'essiccatore: Altezza esterna 3,2 m x larghezza 4,1 m x lunghezza 4,55 m, altezza interna 2,1 m x larghezza 3,8 m x lunghezza 4,1 m. L'essiccatoio è completo, è possibile visitarlo parzialmente costruito. Parti descritte per il montaggio. Materiale alluminio, ottime condizioni. È stato conservato nella sala per 15 anni.

Le caldaie ad acqua calda di tipo G sono utilizzate per riscaldare l'acqua negli impianti di riscaldamento a bassa pressione: per il riscaldamento di edifici con acqua calda, per la preparazione di acqua calda, come fonte di calore per essiccatoi a legna, ecc. Ottime condizioni, usato solo per alcune stagioni Imbuto di riempimento della segatura