lavorazione della lamiera usati in vendita (3,284)

pressure: 110 t: Ø 40x20 mm throat: 500 mmengine output: 9 kWno. of strokes: 28 Hub/minstroke max.: 80 mmweight: 3150 kgAccessories / equipment:- punching tableThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 2,5 mmroll-body distance: 260 mmthroat: 500 mmdistance between roll centers: 92 mmtool adaptor: 35 mmspeed: 3,5 m/mintotal power requirement: 1,5 kWweight of the machine ca.: 295 kgdimensions of the machine ca.: 1200x700x1200 mmDomestic equipments:- motor driven beading machine- 3 sets of bead rollers- Footswitch- Operating instructions in German- CE mark / Declaration of ConformityThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 32 /minPunching force: 60 to throat: 500 mm: 40x11 mm: 350x15 mm: 350x15 mmL-beam 90°: 120x120x10 mm: 45 mmsquare edge steel: 40 mm: 10 mm: Aufnahme bis max. 150x10 engine output: 5,5 kWweight: 2012 kgBasic equipment:- Flat steel shears with knife set- Angle shears with knife set- Punch with quick release device for punches up to 40 mm- Support table for punching device- Triangular notching device- Support table for notching- bending station- Bending stamp with matrices V 40 and V 70- electrical contact stop (1 meter)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 32 /minPunching force: 60 to throat: 250 mm: bis max. Ø 40x11 mm: 350x15 mm: 350x15 mmL-beam 90°: 120x120x10 mm: 45 mmsquare edge steel: 40 mm: 10 mm: Aufnahme bis max. 150x10 engine output: 5,5 kWweight: ca. 1600 kgBasic equipment:- Flat steel shears with knife set- Angle shears with knife set- Punch with quick release device for punches up to 40 mm- Support table for punching device- Triangular notching device- Support table for notching- bending station- Bending stamp with matrices V 40 and V 70- electrical contact stop (1 meter)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Punching force: 45 t hole diameter in sheet thickness: Ø 27x13 mm: 24 /minL-beam 90°: 80x80x8 mmL-beam 45°: 60x60x6 mmflat steel: 200x13 mm: 7 mmengine output: 2,2 kWweight: 760 kgBasic equipment:- Complete set of blades for flat steel shears- Complete knife set for angle steel shears- Compl. Standard punching device- Stamp quick release device for punches up to 27 mm diameter- Rectangular notching device compl. with hold down- notch- Support table for punching deviceThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 40 mm: 8,5 U/min: 120 mmroll diameter: 152 / 162 mmengine output: 1,1 kWrange L-W-H: 900 x 600 x 1000 mmweight: 470 kgconnected load: 400/50 V/HzEquipment / Accessories:- Three driven rollers- Manual delivery of the upper roller- Working position horizontal and vertical- Bearings with tapered roller bearings- Use of replaceable slide rails on the guide carriage- The standard roller set is included. He can turnused different profilesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 4 mmroll-body distance: 260 mmthroat: 500 mmdistance between roll centers: 132 mmtool adaptor: 40 mmspeed: 5 m/mintotal power requirement: 2,2 kWweight of the machine ca.: 350 kgdimensions of the machine ca.: 1650x700x1280 mmDomestic equipments:- motor driven beading machine- 3 sets of bead rollers- Footswitch- Operating instructions in German- CE mark / Declaration of ConformityThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

shaft diameter: 60 mmShaft revolutions: 6 U/minroll diameter: 215 mmpressure hydraulic cylinder: 180 kNdimensions: 1125x870x1620 mmweight: 820 kgAccessories / Equipment:- Three driven rollers- Hydraulic delivery of the upper roller- Working position horizontal and vertical- Digital display with memory function- Bearings with tapered roller bearings- Use of replaceable slide rails on the guide carriage- The standard roller set is included. It can bend various profiles flat iron, T-iron, solid material etc.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: R10-R260 : max. 210 °: 54x2 mm: 42x2,5 mm: 42x3,5 mm: 30 mmbending speed: max. 4 U/minAmount of programms: 30x9 voltage: dreiphasig 220-400 Vtotal power requirement: 1,1 kWdimensions of the machine ca.: 1000 x 410 x 570 mmweight of the machine ca.: 80 kgAccessories / equipment:- Machine structure: aluminum alloy- Base: welded steel- Standard accessories (including footswitch, operating instructions)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mmplate thickness: 6 mmvoltage: 380 Vcontrol: CYBELEC CybTouch down holder: 14 Stückcutting angle: 1,2 °total power requirement: 11 kWweight of the machine ca.: 6.300 kgdimensions of the machine ca.: 4000x2100x1640 mmEquipment:- CNC electr. / hydraulic swing cut shears- CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Quantity Cutting length limitation Material preselection, including sheet thickness Cutting line lighting- motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. can be folded up at max. Traverse path, for longer cuts- 1x side stop- 2x front support arms- Ball casters in the front support table- hinged finger protection, with safety switch- BOSCH / HOERBIGER hydraulic system- SIEMENS electrical system- light barrier behind the machine (safety device)- foot switch- CE mark / declar ...

: 45 to.no. of strokes: 24 Hub/minhole diameter in sheet thickness: max. Ø 27 in 13 mm: 80x80x8 : 60x60x6 mmflat steel: 300x10/200x13 mm: 7 mmengine output: 2.2 kWrange L-W-H: 1550x820x1540 mmweight: 760 kgStandard equipment:- Complete knife set for flat steel shears- complete knife set for angle steel shears- complete standard punching equipment- Stamp quick release device for punches up to Ø 27 mm- Rectangular notching device complete with hold-down device- notch- Support table for punching deviceThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mmplate thickness: 25 mmpre-bending: 20 mmupper roll diameter: 390 mmlower roll diameter: 360 mmside roll diameter: 300 mmtotal power requirement: 18,5 kWweight of the machine ca.: 17.100 kgMachine dimensions approx.: 5800x2100x2000 mmAccessories / equipment:- Conical bending device- induction hardened rolls- digital display for side rollers- Machine made of steel construction- Separate control panel- two speeds- all rollers on ball bearings- Folding and support bearing from the top roller is actuated from the control panel.When the folding bearing is opened, the roller moves automatically upwards.- Conical adjustment of the rollers via control panel- Central rollers are via hydraulic motor and rotary reduction geardriven. (Top and bottom rollers)- CalibrationThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 40 mm: 8,5 U/min: 120 mmroll diameter: 152 / 162 mmengine output: 1,1 kWconnected load: 400/50 V/Hzhydraulic pump: 1,1 kW: 80 kNrange L-W-H: 900 x 600 x 1000 mmweight: 470 kgEquipment / Accessories:- Three driven rollers- Hydraulic delivery of the upper roller- Digital display with memory function- Working position horizontal and vertical- Bearings with tapered roller bearings- Use of replaceable slide rails on the guide carriage- The standard roller set is included. He can turnused different profilesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 28 min.Punching force: 110 to: 40x20 mmflat steel: 600x15 oder 400x20 mmL-beam 90°: 160x160x16 mmL-beam 45°: 70x70x7 mm: 50 mmsquare edge steel: 50 mm: 13 mmthroat: 300 mmBasic equipment:- Complete set of blades for flat steel shears- Complete knife set for bar cutter- Complete knife set for angle steel shears- Compl. Standard punching device- Stamp quick release device for punches up to 40 mm diameter- Rectangle notch compl. with hold downs- Complete knife set below for rectangular notching- Upper tool for rectangular notching- Support table for flat material- Punching table with stop- Notch with stopThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 95 mmShaft diameter: 30 mmShaft revolutions: 7 U/minroll diameter: 132 mmDrive: 0,75 kWweight: 220 kgrange L-W-H: 530x900x660 mmEquipment / Accessories:- Two driven rollers with grooved surface- Manual feed of the upper roller- working position horizontal and vertical (with tilting base)- Bearings with tapered roller bearings- Use of replaceable slide rails on the guide carriage- The standard roller set is included. He can turndifferent profiles are used e.g. Flat iron, T-iron, solid materialetc.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

round material: 40 mmtube diameter: 70x2 mmsquare material: 80x30x3 mmL-beam: 50 x 5 mmI - beam section - flat steel: 80 x 16 mmI-beam section - upend: 50 x 15 mmroll diameter: 157 mmShaft diameter: 50 mmbending speed: 2,95 m/mintotal power requirement: 1,1 kWweight of the machine ca.: 500 kgdimensions of the machine ca.: 1000x950x1450 mmDomestic equipments:- Special steel shafts (42CrMo4) hardened and ground- a set of standard rollers- lower rollers up and down hydraulically deliverable- digital display for lower rollers- separate control panel- in one direction manually adjustable lateral straightening rollers- manual lubrication- horizontal and vertical operation- CE mark / Declaration of Conformity- Operating instructions in GermanThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 40 mm: 8,5 U/min: 120 mmroll diameter: 152 / 162 mmengine output: 1,1 kWconnected load: 400/50 V/Hzhydraulic pump: 1,1 kW: 80 kNrange L-W-H: 900 x 600 x 1000 mmweight: 470 kgEquipment / Accessories:- Three driven rollers- Hydraulic delivery of the upper roller- Digital display with memory function- Working position horizontal and vertical- Bearings with tapered roller bearings- Use of replaceable slide rails on the guide carriage- The standard roller set is included. He can turnused different profilesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1050 mmplate thickness: 1 mmroll diameter: 56 mmdimensions of the machine ca.: 1600 x 700 x 1050 mmDomestic equipments:- Upper roller can be swung out manuallyThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 40 mm: 8,5 U/min: 120 mmroll diameter: 152 / 162 mmengine output: 1,1 kWconnected load: 400/50 V/Hzhydraulic pump: 1,1 kW: 80 kNrange L-W-H: 900 x 600 x 1000 mmweight: 470 kgEquipment / Accessories:- Two driven rollers- Hydraulic delivery of the upper roller- Digital display with memory function- Working position horizontal and vertical- Bearings with tapered roller bearings- Use of replaceable slide rails on the guide carriage- The standard roller set is included. He can turnused different profilesThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2100 mmplate thickness: 13 mmpre-bending: 10 mmupper roll diameter: 230 mmlower roll diameter: 210 mmside roll diameter: 190 mmtotal power requirement: 7,5 kWweight of the machine ca.: 4.620 kgdimensions of the machine ca.: 4150x1400x1300 mmAccessories / equipment:- Conical bending device- induction hardened rolls- digital display for side rollers- Machine made of steel construction- Separate control panel- two speeds- all rollers on ball bearings- Folding and support bearing from the top roller is actuated from the control panel.When the folding bearing is opened, the roller moves automatically upwards.- Conical adjustment of the rollers via control panel- Central rollers are via hydraulic motor and rotary reduction geardriven. (Top and bottom rollers)- CalibrationThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

bending speed: 2.1 m/minBending capacity - square: 30x30 mmbending capacity - flat iron: 80x15 mmBending capacity - flat iron on edge: 50x10 mmtube diameter: 1 oder 60x2 mmShaft diameter - upper: 35 mmShaft diameter - lower: 30 mmtotal power requirement: 0,75 kwrange L-W-H: 650 x 500 x 1300 mmweight: 170 kgStandard features:- hardened special steel shafts- a set of hardened rollers- Bottom rollers are driven- lateral straightening rollers- Foot pedal- horizontal and vertical workingThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 10 mmPunching force: 55 to: 40x10 mmflat steel: 300x15 oder 200x20 mmL-beam 90°: 120x120x10 mmL-beam 45°: 70x70x7 mm: 40 mmsquare edge steel: 40 mm: 37 /min.throat: 250 mmweight of the machine ca.: 1.600 kgBasic equipment:- Complete set of blades for flat steel shears- Complete knife set for bar cutter- Complete knife set for angle steel shears- Compl. Standard punching device- Stamp quick release device for punches up to 40 mm diameter- Rectangle notch compl. with hold downs- Complete knife set below for rectangular notching- Upper tool for rectangular notching- Support table for flat material- Punching table with stop- Notch with stopThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 48x3,5 mm: 48x2,5 mm: 32 mm: 64x2 mmbending speed: 2 U/min: R10-R300 total power requirement: 1,5 kWweight of the machine ca.: 110 kgdimensions of the machine ca.: 410x1000x570 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

plate thickness: 2,5 mmroll-body distance: 260 mmthroat: 500 mmdistance between roll centers: 92 mmtool adaptor: 35 mmspeed: 3,5 m/mintotal power requirement: 1,5+0,55 kWweight of the machine ca.: 320 kgdimensions of the machine ca.: 1200x700x1200 mmDomestic equipments:- motor driven beading machine- 3 sets of bead rollers- Footswitch- Operating instructions in German- CE mark / Declaration of ConformityThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

flat steel: 350 x 10 mmround bar steel: 35 mmsquare edge steel: 30 mmL-beam: 80x80x8 mmhole diameter in sheet thickness: Ø 27 in 13 bzw. Ø 20 in 8 mm: 500 kNthroat: 177 mm: 34 (Hub 15mm)blade length: 356 mmengine output: 3.0 kWweight: 950 kgdimensions: 1300x1100x1850 mmStandard equipment:- Knife set for flat steel- Complete knife set for angle steel shears- Complete normal punching equipment- Quick release device for punches up to 31 mm- Support table for punching device, rectangular notching and flat steel shears- Bending stamp with matrices V 40 and V 70- Electric contact stop (1.000 mm)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll diameter: 215 mmshaft diameter: 60 mmShaft revolutions: 6 U/min: 100x2 mm: 80x15 mmpressure hydraulic cylinder: 180 kNtotal power requirement: 2,2 kWweight: 720 kgdimensions: 1200x900x1700 mmAccessories / Equipment:- Three driven rollers- Hydraulic delivery of the upper roller- Working position horizontal and vertical- Digital display with memory function- Bearings with tapered roller bearings- Use of replaceable slide rails on the guide carriage- The standard roller set is included. It can bend various profiles flat iron, T-iron, solid material etc.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 60x3 mm: 60x2,5 mm: 35 mm: 64x4 mm: R10-R300 bending speed: 2 U/mintotal power requirement: 1,5 kWweight of the machine ca.: 130 kgdimensions of the machine ca.: 595x363x900 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

stroke: 70 mmwork height max.: 1094 mmthroat: 500 mm: 40 in 14 mmno. of strokes: 20 Hub/minthroat: 500 mm: 80 toengine output: 9 kWrange L-W-H: 1980x1150x2000 mmweight: 2000 kgAccessories / equipment:- punching tableThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mmplate thickness: 10 mmpre-bending: 8 mmupper roll diameter: 270 mmlower roll diameter: 250 mmside roll diameter: 210 mmtotal power requirement: 11 kWweight of the machine ca.: 7750 kgOverall size: 5600x1450x1600 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

: 50 mm: 8,5 U/min: 100 kNroll diameter: 162 mmDrive: 1,5 kWrange L-W-H: 1100x850x1350 mmweight: 495 kgEquipment / Accessories:- Two driven rollers- Hydraulic delivery of the upper roller- Digital display with memory function- Working position horizontal and vertical- Bearings with tapered roller bearings- Use of replaceable slide rails on the guide carriage- Footswitch- standard roller setThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.